FAQs on CO2 Canopies for Planted Tanks

Related Articles: Components of Planted Aquariums, Carbon dioxide and the planted freshwater aquarium by Neale Monks, Tanks and Stands for the Aquarium Garden

Construction of a CO2 Canopy for Plant Tanks

By -- Lalith Atugoda E-mail -- [email protected]

I was recently taken up on the subject of Aquarium Planting and the Aquarium related Web sites helped me a lot to gain valuable knowledge on many basic points. We living in Sri Lanka do not have that much of Aqua related equipment at affordable prices. So I was fascinated reading the article ' CO2 Yeast Reactor ' by Jim Kelly.

The CO2 Generator, I made accordingly worked perfectly to my great satisfaction. Also I came across the fact that if we can have CO2, contacting with water for a longer time, then even a bigger Plant tank can be accommodated with the CO2 Yeast reactor.

I have made a Do-it- yourself CO2 Canopy with the use of clear Plexiglas sheets and clear Silicon Sealant which can be easily camouflaged by the plants themselves so the beauty of the Plant tank will not be spoiled.

The Plus points of the system are

Your valuable CO2 gas will be in contact with water more time giving the plants the vital CO2 provision.

The Length and the Width of the CO2 Canopy unit can be customized to dimensions of the Plant tank and to the individual taste [Ex- To reduce the width and to increase the length etc.]

The number of canopies can be increased or decreased at the time of the construction according to each person's requirement.

Once the multi unit Canopy is constructed and in use, if one thinks the CO2 mixture is too rich , one can easily reduce the number of canopies used for CO2, just by inserting the CO2 outlet plastic tube to a upper order canopy in the canopy stack.

If one wishes to purge the Canopy chambers , an aerator output can be connected to the in-line socket provided outside the tank of the CO2 feeding plastic tube for a few minutes

Construction Details

The unit I constructed having three canopies measures 12 in [L] x 6 in [W] x 2 in [D]

( 30 cm x 15 cm x 5 cm). The finished CO2 Canopy unit was fixed to the center of the inner backside glass of my 32' x 12' x 12' Glass tank.

I thought a sketch would be better than describing in writing. So kindly refer to sketches provided.

Removing small triangular shaped pieces from top ends of Plexiglas hood pieces would make its upper edge contacting the Back Plexiglas piece , if you first finish off the units U shaped section. Once this section is bonded properly , then you can arrange the hood pieces and apply sealant to edges.

I found that the slowly accumulating CO2 gas in the bottom canopy is released to its upper canopy via the hole provided in series of large bubbles with a force that some gas forced out of the canopy cover without being trapped in the upper canopy cover. To overcome this problem, a 5 cm Plexiglass strip was centered and adhered to slanted canopy hoods in line of Canopy hood holes to prevent big CO2 bubbles leaking from canopy hoods . The top most canopy actually does not need a vent hole as it is the last CO2 chamber but I provided one in my design. To be more innovative, the vent holes were arranged alternatively at sides of each canopy hood in my design so that separate pieces of Plexiglass had to be fixed centering each vent hole. If you like a simple method, then you can have vent holes of all canopy hoods in one side and in one line so that you can paste one stripe of Plexiglass to slanted canopy hoods avoiding CO2 Bubble leaking to outside. It is better to leave about half inch or more from the bottom of a slanted canopy hood to the top edge of the lower canopy hood. The 6 mm hole can be made in this portion to insert CO2 inlet plastic tube. Also make sure that you apply the sealant properly so that there will be no leaks from canopy hoods. Double check before you install the unit in the Plant tank by inserting the unit into a water tank and filling the chambers with air --use an aerator or you simply can blow some air from mouth through a plastic tube directed under the bottom canopy hood. Once all chambers are filled with air, stop giving air and watch for leaks . If a chamber gets filled with water completely, then there is a leak from the canopy hood. If everything is OK then adhere the unit to back glass of the Plant tank using sealant.

Notes to Take Care

I was using the Yeast reactor to generate CO2 gas for the Canopy. Initially when I was testing the unit, the tank was without any plants but filled with water 2.5 cm from the top. It took nearly 30 minutes for the accumulated CO2 in the bottom canopy to release to the upper canopy in a series of bubble bursts which started a chain reaction releasing CO2 to other canopy and finally through the hole at top canopy to outside. Once I planted my tank fully and using a 20W TFC Fluorescent lamp I noticed that the bottom canopy didn't release the CO2 to upper chamber at all ! The reason I think was the fact that the plants started using dissolved CO2 from the water that the incoming CO2 had been constantly getting dissolved in water so CO2 pressure built-up in the bottom canopy was not being forceful enough to get released to the upper chamber.

I reasoned out the following from my experience.

With one 2 Liter CO2 Yeast Reactor, the number of canopies required for my Plant tank will be a single one. As the bubbling rate of my unit is about one 3 mm dia bubble every 4 seconds , I thought increasing the bubbling rate would give the required amount of CO2 to other canopies. Increasing the bubbling rate by adding some more Yeast just did the trick. Those who have commercially pressurized CO2 cylinders can easily overcome the problem I faced but one has to be mindful whether too much of CO2 would then concentrate the water.

It seems CO2 concentration in water makes changes to the water PH value. So take this fact into consideration.

Hope this would be an interesting project to Aquarium Plant lovers and I hope one can experiment with the unit to gain better results.

List of Material and Tools needed for the construction of the CO2 Canopy

Clear Plexiglas 2-3 mm thick

Clear Silicon Sealant

Sealant Gun

Scriber tool to groove the Perspex (aka Plexiglas) sheet

Metal Ruler to guide the scriber tool to make cuts

Drill bits 3 mm and 6 mm Diameter

Adhesive tape/Books etc. to first arrange the Plexiglas pieces before applying sealant

Sketches

I hope the sketches provided below would make it easy to construct the CO2 Canopy.

Please visit our Sponsors